How to float fasten a snap to the rod?

Modern centrifugal telescopic fishing rod carbon available on the market without elements for fastener snap. At the same time we want to attach a fishing line to the rod tip with a quick change to another. Agree that in the absence of the necessary improvements, this procedure takes a lot of time. There are some simple ways secure attachment of the fishing line with a float snap on the rod allowing you to quickly mount the float snap-in before fishing and take off after fishing, and also for a quick change Lesnoy one snap to another, depending on the conditions of fishing floats fish size.

Methods of attachment of the fishing line to the rod tip

Mount the fishing line snap connector

The most practical for quick and convenient access method allows you to use special plastic satiku connector. It is matched to the diameter of the tip of the whip at the bait shop. Mounted on the whip with superglue. The connector has eyelet for attaching fishing line.

Mount the fishing line string through

In the absence of a connector in this way is very simple and can reliably fasten the fishing line to the rod tip. How to do it?
First, the tip of the whip rod must be glued with a few drops of “fast” epoxy cut nylon lace long, 20-30 mm, so that the tip was inserted inside the lace for 10 mm.

At the opposite end of the strap fit the site, and with the help of open fire melted the tip. At the end of the fishing line snap is a large loop for attaching a noose on the lanyard and a loop for removing fishing line after catching.

READ  Fishing for bream in the summer with a float rod

Mount two cambricum

You will need two small cut kembrikom 50-100 mm. the First sleeve is selected according to the diameter of the tip of the whip and put on him at the distance of 100-150 mm from the end. The second sleeve fits over the tip of the tip. A plastic tube before the first noose is attached to fishing line tackle, and then is wound multiple turns after putting on the second cambrica fishing line securely. Before fixing the line pull for a tight fit to the whip.

You need to make snap-ins

In addition to the parts we talked about, you will need a silicone end sleeves of different diameters, a nice small pliers, small sharp scissors or nail clippers. It will not hurt as a device for removing pellets from the fishing line. Very useful I think petlevski and calibrators loops: they allow you to quickly and efficiently do loops are almost identical in size. Of course snap can be linked and a reservoir. But I think that it is better to do it at home, in a relaxed atmosphere.

Just where to get “pond” of suitable depth? Sold a proprietary plastic “flask”; however, are not cheap. They, incidentally, could easily replace the design of plastic water pipe with a diameter of 120-150 mm and a length of 600-800 mm with a tight ending. All items can be purchased on the construction market. For these purposes it is possible to accommodate a tall glass vase, which in the intervals between the manufacturer of snap-ins will serve as interior decoration. In an extreme case, fit and cut a plastic bottle, although its heights are often insufficient.

READ  How to ship a float

Finally, we need the motoviltse for storage and transportation of snap-ins. Match them to the basis of the dimensions of the used float. The float must freely and comfortably placed between the walls of motoviltse, and the antenna must not protrude beyond it. In this case, the float would be well-protected from accidental damage during transport. Taking a broader motoviltse, you can place two snap-in.

Snap-in reel starting from the hook that attaches over one of the crossbars. For the case when you are transporting a snap without a leash, at the ends of motoviltse provides pins for attachment loops. Wound fishing line (for fishing rod centrifugal its length should be such that in the operating state, the hook never reached the butt of 300-400 mm), gently have the float… need to fix the end of the snap, as not always its length will allow you to throw a loop on a pin, or a ledge wall. Some have a special motoviltse mobile devices for fixing the end of the loop. If not, you can use homemade or branded rubber anchor.

Leave a Reply

Your email address will not be published. Required fields are marked *