How to attach the bait float

How to attach the bait float? This question, especially for beginners in fishing, it seems complicated is that the floats are mostly sold without kembrikom for fastening to a fishing line.

The attachment of the floats to a dull snap

The easiest way of fastening — regular cambricum or selected according to the size of the keel of the float to the fishing line passed in with a slight interference fit. Fishing line threaded down through the top ring of the float and is attached to one or two cambricum. The first is very short (5 mm) sleeve is put near the body of the float, departing from it by 5-10 mm; the second, 10-15 mm in length, is on the tip of the keel, so that part cambrica remained needyou on the keel. In this case, the line almost never salesteams for the keel. End sleeves it is best to choose modern silicone. They are more reliable fixed line and less deform it when they change depth when moving on the line. However, it is quite suitable and conventional PVC, but they have more to pick exactly at the inner diameter. Ideal option when the fishing line is pulled in cambrige. put on the keel of the float, with little effort.

I almost completely abandoned the top cambrica, replacing it with an elongated (length about 20 mm) lower. Such a mounting method, in my opinion, is convenient because if a strong tension fishing line (hook or playing a fish) and keel, slightly curving, does not allow it to penetrate the coating of the body of the float, and also reduces the load on the ring. The magnitude of this load can be judged by taut, like a bowstring, the line between the two cambricum (especially if they are worn with some effort), and curved keel of the float, for example, after the lead break. If you have to significantly change the depth of fishing (much to move the float), I simply remove the sleeve, move the float to the desired place and then wear sleeve. It protects the floats from damage. In General, moving the float to the fishing line, it is necessary to always make sure that she not cut a groove in the cover float. Some floats fishing line can take place inside his body: along the keel or pasted through a tube. It protects the float from damage by the fishing line. For floats with a ring at the bottom and one mounting point is easy to fabricate an adapter from a suitable copper wire.

READ  Successful fishing for catfish from a boat

Now spread the floats with hole for fishing line inside along the keel of the float. These floats are good for power fishing (especially carp) and “zatsepistye”. Fishing line, passing inside of the float, can not physically damage the float under heavy load, since the stress on the body float there. Options for fixing this float several. The easiest is to thread the fishing line inside the body, insert the keel and fix the line at the end of the keel cut silicone cambrica. This option is great for carp fishing to surround the nozzle, in this case, the float does not loads in addition. For more delicate fishing I like the option of a short (3-5 mm) cut hard cambrica. It is put on fishing line and mounted on the antenna above the body of the float. This sleeve performs an important role: carries a second attachment point of the float above the antenna that allows you to adjust the float very sensitive. When you post it will be much less out of the water, and means responsive even on low bite. Sleeve must be chosen so that it fits over the antenna with a little tension, not too pinched line. Danger to cut it at the toe or otherwise not, as the fishing line is always along the float. In the Arsenal of poplavochnye have to be a set of several kembrikom.

It is, relatively speaking, the standard methods of fastening the float. But the situation in fishing are different, and it is necessary to change the tackle to match the fishing conditions. For example, in a crosswind to reduce the demolition equipment. For this you need to lower the point of attachment of the float to a fishing line. To mount only one, even durable and tight a plastic tube is not necessary, it can come off, for example at the toe. There is a simple method that can be applied directly into fishing. Cut fishing line slightly thicker than the snap on, should be tied to the end of the keel of the float in the same node, which is tied the hook. Bundle for reliability, you can cover the quick-drying glue.

That line didn’t rabovladelcheskim, the site is best to pull the cut cambrica. The other end of the fishing line to tie the basic slip knot (stopper knot for sliding floats) to be able to move it along the wire, setting the depth of fishing. Of course, this method of mounting eliminates wiring a snap, but fishing for bream or carp it is sometimes not necessary — they prefer fixed nozzle and dragging across the bottom will not be interested. To enhance the effect of the lower sinker (shepherd boy) put on the bottom. After casting the fishing line from the float to the end of the stamp rod, so the tooling remains almost motionless. To fully eliminate the influence of surface currents can be above the float to hang an extra pellet No. 12-13, which is imbedded the line at greater depth.

READ  Night hunting.

The same scheme of fastening of a float on a short leash is perfect for fishing ultra-light snap-in (capacity less 0.5 g) in strong winds. Wind this snap-in is blown out of the water is much weaker. Of course, on very light tackle additional sinker not put. Mounting on floats with one attachment point (rather conditionally called Amateur) usually involves the use of Cambria. I like the fixing unit in the form of a twisted wire with the eyelet — so the float is securely held, easily removed and can move and swivel eliminates the overlap of the line. But often on the float there is only a ring, it is also possible to mount the fishing line, for example, zahlestnuv loop, or use the mounting scheme on a short leash, as described above. But safer to make a loop from a suitable brass or soft stainless steel wire. If it is assumed that the float is removable, can accommodate a small clasp with swivel — fishing line is passed him twice and stopped in small pellets. It turns a simple and reliable mount for quick release float.

Mount the float on the Bologna tackle

Mounting options are basically the same as with a dull snap, only the sleeve must be reinforced with a thicker wall because the load on it increases substantially. Homemade adapter, bent steel wires that are required for rigid fixation of the float on the fishing line. I have not once had to face the fact that due to the high loads on the float crashes top fastening — ring, glued into the body of the float. Therefore it is necessary beforehand to check and if necessary reinforce with a drop of glue. Significantly different fastening Bologna sliding float. He has two rings through which is threaded the fishing line and reaching the stopper knot, the float fixed on the line put on a bead. Locking the knot fit in the same fishing line as the main line.

READ  Demi-season suit Gorka

Deaf mount match float

Perhaps the most sophisticated types of fasteners anglers invented just for this tackle. All of them are used for specific fishing circumstances. The easiest option is to mount a swivel clasp. In the loop of the double-threaded fishing line swivel and stopper it in the right place two or three pellets. The clasp is better to take medium size, as little sometimes does not withstand the loads during power casting. When you throw close to the shore, it is quite suitable version of the twist of wire with a loop, only the length of strand to be wearing a sleeve should be more — 15-20 mm. the Advantage of this option before the previous in the ease of movement of the float to the fishing line. It is very good for light floats and floats of type “multicolor”.

Fixing sliding float

Sliding floats should move freely along the wire. For attaching them is the easiest way to use the same swivel with a carabiner. The swivel rests against the retaining bead, which, in turn, stops the knot. If at hand there was no suitable beads, a simple solution would be a ring of a swivel, gliding along the line. It is tight with pliers until the hole size is slightly larger than the diameter of the fishing line; fishing line it will pass freely, while retaining the knot will be securely inhibited without getting stuck. Perhaps, only for floats of type slider you need a special adapter that deviate from the line and do not intersect with her in flight and while landing. But here, you can get out of the situation using the means at hand. For the swivel clasp and compressed ring for the passage of fishing line (as in the previous option) pull the shrink tube and heat it. It’s rather hard working design. So literally improvised means you can easily and securely attach a variety of options for floats.

Leave a Reply

Your email address will not be published. Required fields are marked *