Knit yourself a snap to feeder

Many of you are familiar with feeder. Its main component is the feeder equipment. It allows you to feel even the slightest movement of the fish, and helps to overfeed the desired area of the reservoir.

Today there are many snap-ins for feeder rods, but not all of them work effectively. The most popular among fishermen Federico the following gear:

  • The most effective equipment is the paternoster. It is reliable, and is able to give a good result.
  • Another type of snap – loop Gardner. This device is easy to fabricate and to mount on the rod, however, it is not so sensitive (compared to an asymmetric loop).
  • Asymmetrical loop is a very sensitive tackle. Basically, it is used for fishing on reservoirs with a rapid current, since snap does not allow the leash to twist around the main cord.
  • A symmetrical loop. This item donkey similar to above described, but is used for fishing in quiet waters.
  • Anglers have perfected the paternoster, thus there tackle a helicopter. Its peculiarity is the method of mounting the trough at the end of the line, where’s the leash slip just above it. The gear used for fishing are not very active fish in fast rivers.
  • Protivotankovaya tackle. In this device, the feeder is fixed to the tube, and is threaded inside the fishing line. Due to the large number of extra elements to catch the fish hard enough.
  • Harvester (spring). He is something of a cross between protivotankovaya tackle and paternoster, where a feeder strapped to the tube with a piece of twine. The device is good because when you lose the toe only one feeder and not all the attachments.
  • READ  Fishing for carp in the spring on a feeder

    Manufacturer of paternoster

    Work will not take much time, especially if you are familiar with the art of knitting fishing knots. Simple tackle is that the nodes are tied only on the main line. First, make a small loop with one end. Later it will snap the leash. From the first step back loop of about 10-15 cm, and fit in an additional loop, the dimensions of which will directly depend on the method of installation of the feeders.

    When fastening method “loop in loop” value loop should be choose as when you mount with swivel and carbine.

    How to make asymmetrical and symmetrical loop

    To tie a steel loop you need to take a five-foot piece of tough and thick fishing line. It needs to be folded in half so that one side was longer than the other by several centimetres. Next, knit a double knot to connect the loop with the main line. Now the most important part: you must bind the bypass leash at the same time, it should always be in the vertical position. It will not allow the leash to overlap with the main cord.

    Then twist the two segments of fishing line so that you have got a fragment with a length of about fifteen centimeters. At the end of it fit a double knot. The swivel is fixed on the extended end of the line. Now counting required cut the cord and tighten a knot in it. In most cases, the length of the short segment is about forty centimeters, and longer – about half a meter.

    READ  Secrets of fishing on the Colorado potato beetle

    Symmetrical tooling is made in exactly the same way. The only difference is that the ends of both segments are equal. Then by the end of the snap is attached to the swivel. He will combine a symmetric loop with the main line.

    The snap-in “helicopter”

    A piece of fishing line dresses toporok and swivel, joined by a leash with a plastic tube. At the end of the cord set clasp (we subsequently attach the feeder).

    On one eyelet of the swivel tight fit sleeve. In most cases feeders are mounted at a distance of approximately twenty inches from the leash, but some fishermen measure a shorter distance. The main condition is firmly stops in one position.

    Equipment for feeder with protivoparazitarian

    This rigging is very simple and is very popular. Make it thus: put a piece of tube to the main thread, and fix its one end bead, and the second swivel. To the swivel tie a leash. At the same time, a long fragment of the tubing is rotated to a leash to eliminate overlap of the line.


    The main element of this snap-in is tuba-protivogerpetical, but to the Central swivel is tied a ten inch loop, which is connected with the feeder. Fishermen are constantly experimenting with this tackle, picking up fragments of tubes of varying length and varying size loops. Inside the tube is the main line, fixed a plastic tube.


    In this gear the feeder connected to the main line using the rifle. Cut edge on which slides the feeder limit special latches. At the end of the main cord secured on a leash.

    READ  Bait with a rotating petal, differences and peculiarities

    If You’ve read this far, You have been helpful, so please subscribe to our channel on Yandex.Zenand put a like (thumbs up) for us works. Thank you!

    Leave a Reply

    Your email address will not be published. Required fields are marked *